Omron AUTOMATION

TK 12000

Course Fee TK 10000

Omron plc
Class
Class Topic
01Introduction and understanding of Switching Contacts- NO/NC devices.
02introduction to various types of sensors.
03load controlling using various types of sensors
04Specification, selection & connection diagram of Magnetic contactor.
05load controlling practical practice using magnetic contactor
06Specification, selection & connection diagram of Magnetic Relay.
07Load controlling circuit practical practice by using magnetic relay.
08Specification, selection & connection diagram of On delay timer.
09Load control circuit practical practice by using on delay timer.
10Specification, selection & connection diagram of Off delay timer.
11Load control circuit practical practice by using off delay timer.
12Specification, selection & connection diagram of twin timer/Sequential Timer.
13Load control circuit practical practice by using twin timer/Sequential Timer.
14INTRODUCTION TO PLC AUTOMATION.
15DISCUSS ABOUT PLC INPUT ELEMENT.
16DISCUSS ABOUT PLC OUTPUT ELEMENT.
17DISCUSS ABOUT PLC INPUT MODULE/OUTPUT MODULE.
18DISCUSS ABOUT PLC ADDRESSING.
19FAMILIARIZATION WITH VARIOUS PLC LANGUAGES.
20BLOCK DIAGRAM OF PLC.
21CONCEPT ABOUT LADDER.
22BASIC CONCEPT OF PLC SOFTWARE & DATA CABLE
23OVERVIEW & INSTALLATION OF CX PROGRAMMER.
24FAMILIARIZATION WITH VARIOUS LADDER SYMBOL
25LOAD CONTROLLING WITHOUT LATCHING CIRCUIT PRACTICAL PRACTICE
26LOAD CONTROLLING WITH LATCHING PRACTICAL PRACTICE
27INTRODUCTION TO SET-RESET COMMAND.
28LOAD CONTROLLING USING SET RESET COMMAND.
29INTRODUCTION TO ZONE RESET COMMAND.
30FAMILIARIZATION WITH INTERNAL AUXILIARY RELAY IN PLC
31COMPARISON BETWEEN GENERAL AUXILIARY RELAY AND BATTERY BACKED AUXILIARY RELAY
32FAMILIARIZATION WITH DIFFERENT TYPE OF INTERNAL TIMERS IN PLC.
33COUNTING SYSTEM AND LOGIC OF INTERNAL ON DELAY TIMERS IN PLC.
34DIFFERENCE BETWEEN NORMAL TIMERS AND RETENTIVE TIMERS.
35ON DELAY TIMER LOGIC PRACTICAL PRACTICE
36DESIGNING A TWIN TIMER USING ON DELAY TIMER.
37GENERAL TIMER VS RETENTIVE TIMER PRACTICAL PRACTICE
38DESIGN OF A COMPLICATED PROJECT USING MULTIPLE TIMERS AS PER REQUIREMENT.
39DESIGN A TRAFFIC CIRCUIT USING MULTIPLE TIMERS.
40FAMILIARIZATION WITH DIFFERENT TYPES OF COUNTERS IN PLC
41COUNTER COMBINED WITH TIMER & SENSOR PRACTICAL PRACTICE.
42STAR-DELTA CIRCUIT PRACTICAL PRACTICE IN PLC.
43FAMILIARIZATION WITH VARIOUS TYPES OF DATA REGISTERS IN PLC
44PROGRAMMING OF DATA REGISTERS COMBINED WITH INCREMENT, DECREMENT & DATA REGISTERS.
45TIMER COMBINED WITH DATA REGISTER PROGRAMMING PRACTICE
46COUNTERS COMBINED WITH DATA REGISTER PROGRAMMING PRACTICE
47FAMILIARIZATION WITH ARITHMETIC COMMANDS.
48PROGRAMMING PRACTICE USING ARITHMETIC COMMANDS.
49INTRODUCTION TO “COMPARISON” COMMAND IN PLC.
50INTRODUCTION TO “MOV “COMMAND.
51PROGRAMMING PRACTICE USING COMPARISON COMMAND
52PROGRAMMING PRACTICE USING MOV COMMAND.
53INTRODUCTION TO “CMP” COMMAND
54PROGRAMMING PRACTICE USING CMP COMMAND.
55INTRODUCTION AND PROGRAMMING PRACTICE USING “CALL JUMP” COMMAND.
56MOTOR AND PUMP CONTROLLING LOGIC PRACTICAL PRACTICE USING TIMER AND INTERLOCKING CONCEPT.
57LOAD CONTROLLING LOGIC PRACTICAL PRACTICE COMBINED WITH TIMER AND COMPARE COMMAND.
58DESIGN A TRAFFIC LIGHT SIMULATOR BY FOLLOWING A CERTAIN DATA TABLE AND ADVANCED COMMANDS.
59DESIGN A LOGIC TO OPERATE MULTIPLE LOAD USING “COMPARE” & COUNTER COMMAND.
60DESIGN A LOGIC TO MANUPULATE THE OPERATING TIME OF A LOAD USING “MOV” COMMAND.
61DESIGN A LOGIC TO CHANGE THE OPERATING TIME OF A TIMER AS PER OPERATOR’S REQUIREMENT USING “INCREMENT” & “DECREMENT” COMMAND.
62PROGRAM READ/WRITE PROCESS USING DATA CABLE.
63ONLINE MONITORING & TROUBLE SHOOTING PROCESS FROM PC/LAPTOP PRACTICAL PRACTICE.
64PROCESS OF CONTROLLING AC LOAD USING DC SUPPLY OR CONTROLLING DC LOAD USING AC SUPPLY PRACTICA PRACTICE.
65POWER SUPPLY & WIRING OF INPUTS PRACTICAL PRACTICE.
66WIRING OF OUTPUTS PRACTICAL PRACTICE.

OMRON VFD/ FREQUENCY INVERTER PROGRAMMING, CONNECTION, MOTOR RUN, TROUBLESHOOTING
Class
Class Topic
01EVERYTHING ABOUT VFD.
02SPECIFICATION, SELECTION AND CONNECTION PROCEDURE OF THREE PHASE INDUCTION MOTOR.
03MEASURING PROCEDURE PRACTICAL PRACTICE BY USING MULTIMETER.
04MEASURING PROCEDURE PRACTICAL PRACTICE BY USING CLAMP ON METER
05MOTOR CHECKING PROCEDURE FROM MULTIMETER.
06STAR CONNECTION PHYSICAL PRACTICE.
07DELTA CONNECTION PHYSICAL PRACTICE
08VFD HARDWARE DESCRIPTION.
09PRACTICAL CONNECTION OF MOTOR WITH INVERTER.
10INTRODUCTION TO VFD EXTERNAL MODE.
11VFD EXTERNAL MODE WIRING PRACTICAL PRACTICE.
12VFD OPERATION MODE SELECTION
13VFD PARAMETER SETTING.
14VFD FAULT FINDING AND TROUBLE SHOOTING.

OMRON HUMAN MACHINE INTERFACE (HMI) PROGRAMMING, CONNECTION & LOAD CONTROLLING
Class
Class Topic
01INTRODUCTION TO HMI – UNDERSTANDING WIRING & INSTALLATION
02INTRODUCTION TO VARIOUS TYPES OF SWITCH (MOMENTARY, MAINTAINED, SET, RESET ETC.)
03SET/RESET BUTTON FUNCTIONS PRACTICAL PRACTICE.
04INTRODUCTION TO HMI DISPLAY ELEMENTS.
05BUTTON FUNCTIONS-SET CONSTANTS, INCREMENT & DECREMENT & PRACTICAL IMPLEMENTION ON LOADS.
06INTRODUCTION TO SIMPLE & MULTI STATE INDICATORS IN HMI & LOAD CONTROLLING PRACTICAL PRACTICE.
07INTRODUCTION T0 MULTI STATE BUTTONS IN HMI & LOAD CONTROLLING PRACTICAL PRACTICE.
08INTRODUCTION TO NUMERIC DISPLAY FOR DISPLAYING NUMBER, COUNTS OR PRODUCTION & LOAD CONTROLLING PRACTICAL PRACTICE.
09INTRODUCTION TO NUMERIC ENTRY FOR GIVING THE INPUT FROM HMI & LOAD CONTROLLING PRACTICAL PRACTICE.
10INTRODUCTION TO NUMERIC DISPLAY & GAIN SETTING IN NUMERIC DISPLAY
11INTRODUCTION TO MOVING SIGN & PRACTICAL IMPLEMENTATION
12OPERATING AND SETTING OF MULTIPLE SCREENS IN HMI & PRACTICAL IMPLEMENTATION.
13HMI CONNECTION PROCEDURE WITH LAPTOP/COMPUTER.
14DATA TRANSFER PROCESS & TROUBLESHOOTING FROM PC/LAPTOP.

Leave a Reply

Your email address will not be published. Required fields are marked *